Boiler Control System Design

Contact Us

Product thermal capacity: 0.7 - 14 MW

Working pressure: 0.7 - 1.25 Mpa

Available fuel: Nature gas, coke oven gas, biogas, methanol, liquid propane gas, diesel, heavy oil, light oil, crude oil, etc.

Available industries: Heat supplying, hospital, hotel.

Introduction

WNS series horizontal internal combustion boiler is classic 3-pass wetback oil/gas fired boiler. After fuel is atomized by burner, flame is full of the wave furnace and transfer heat via furnace wall, called 1st pass; the high temperature flue gasses are collected in reversal chamber and then enter 2nd pass, which is grooved tube bundle area through heat convection, air temperature gradually falls and flows to front smoke box and enter 3rd pass, which is done in the smooth tube bundle area, and then through back smoke box lead to chimney and exhausted to the atmosphere.

Technical Advantages

Digitized Manufacture

The key processes including material cutting, rolling, drilling are made by advanced CNC machining process to reduce the assembly stress and extend boiler working lifetime.
The front and back smoke chamber plates are cut by CNC plasma cutting machine with tidy and beautiful look.

Easy Operation and Maintenance

Fully intelligent operation, with automatic adjustment and protection of burning, water level, temperature and steam pressure. The smoke box door uses the hinge structure for easy inspection, inventory and cleaning.

Long Service Life

The way to weld Smoke tube and tube sheet is to first expand to eliminate the gap between them, then adopt automatic argon arc welding to relief the stress and expand boiler service life.
Longitudinal and girth joint adopt advanced automatic submerged-arc welding for good welding quality. All longitudinal and girth joint are test by radiographic inspection.
Fin tube uses ND steel or stainless-steel material to avoid corrosion in the low temperature.
Inspection stops are set up to guarantee the sequence of expanding and welding to avoid cracking of the tube sheet holes.

Less Fuel Consumption

High quality aluminum silicate fiber is used with fire clay insulation, to control the boiler body temperature below 45℃ and reduce heat lost.
Sufficient steam storage room and heating area to generate high quality steam and high thermal power.
Condenser is added to recycle the waste heat of the exhausted smoke to increase feeding water’s temperature and reduce flue gas emission temperature and increase the thermal efficiency over 98% and save operating cost.

Modern HydronicSystem Designs for Condensing Boile

2016-9-7 · System Flow Greater Than Boiler Flow • Mixing occurs in the manifold • Boiler must modulate higher to meet setpoint demand –Reduced thermal efficiency at higher firing rate –May cause nuisance MRHL trips • Boiler and system return temperatures are equal Monday, December 01, 2014 Modern Hydronic Designs For Condensing Boilers 12

PLC & SCADA Based Effective Boiler Automation Syste

2015-5-22 · So a reliable monitoring system is necessary to avoid catastrophic failure, which is achieved by Programmable Logic Controller & Supervisory Control and Data Acquisition system. This paper outlines the design and development of boiler automation system using PLC, SCADA and sensors. PLC and SCADA interfaced via communication cables.

Steam power plant configuration, design, and contr

2015-1-10 · Steam power plant configuration, design, and control Xiao Wu,1 Jiong Shen,1 Yiguo Li1 and Kwang Y. Lee2∗ This article provides an overview of fossil-fuel power plant (FFPP) configura-tion, design and especially, the control technology, both the conventional and the advanced technologies. First, a brief introduction of FFPP fundamentals and con-

control system design of boiler drum level Archive

2019-10-13 · Drum Level Control Systems are used extensively throughout the process industries and the Utilities to control the level of boiling water contained in boiler drums on process plant and help

Design of interactive control system for industrial boil

2018-12-8 · Design of interactive control system for industrial boiler Zhonghua Shi 1, a, Hongguo Yu 1, b 1School of electrical engineering, Binzhou University, Binzhou 256600, China. , Abstract With the rapid development of modern industry, industrial boiler control system

Steam System Design and Best Practices Related to Kil

2015-9-23 · New England Kiln Drying Association – Steam Design & Best Practices – HerLine Technologies Steam Distribution System Proper layout design & pipe sizing of mains Piping always pitched in the direction of flow Use of eccentric reducers to eliminate creation of condensate collection points (low spots) in piping

Control System Design - MIT OpenCourseWa

2019-8-16 · • Allows the use of graphical methods to predict system performance without solving the differential equations of the system. These include response, steady state behavior, and transient behavior. • Mainly used in control system analysis and design.

Boiler dynamics and control in nuclear power stations

2019-5-21 · 5. Control Scheme Analysis and Design 5.1 Existing Control Scheme The existing PFR boiler control scheme is shown schematically in Figure *f and can be seen to consist of three separate loops. The steam raising plant consists of three drums each with

Boiler Control Systems | Boiler Control Panel Buildin

The boiler combustion control testing center allows IB&M technicians to design boiler instrumentation panels and actually test panels at our location by way of our boiler simulation test center. Customers can come to our facilities and operate their new system and receive training in our panel shop before the new control system is ever

Remote Boiler Monitoring & Control System | BoilerLi

BoilerLink is a proprietary Combustion Control System designed, engineered, and supported by Powerhouse. BoilerLink can interface with and monitor burner management systems (BMS) from any OEM. The BoilerLink system is built using the highest quality components and programmed by Powerhouse's boiler experts.

Design and application of control system for 600 M

Design and application of control system for 600 MW supercritical W shape flame boiler unit ZHU Nengfei 1, LIN Dazhong 2, SONG Lihong 1 1.Guodian Nanjing Automation Company Limited, Nanjing 210031, China; 2.Sichuan Huadian Gongxian Power Generation