Hot Water Boiler Feed Pumps

Contact Us

Other Links

Product thermal capacity: 0.7 - 14 MW

Working pressure: 0.7 - 1.25 Mpa

Available fuel: Nature gas, coke oven gas, biogas, methanol, liquid propane gas, diesel, heavy oil, light oil, crude oil, etc.

Available industries: Heat supplying, hospital, hotel.

Introduction

WNS series horizontal internal combustion boiler is classic 3-pass wetback oil/gas fired boiler. After fuel is atomized by burner, flame is full of the wave furnace and transfer heat via furnace wall, called 1st pass; the high temperature flue gasses are collected in reversal chamber and then enter 2nd pass, which is grooved tube bundle area through heat convection, air temperature gradually falls and flows to front smoke box and enter 3rd pass, which is done in the smooth tube bundle area, and then through back smoke box lead to chimney and exhausted to the atmosphere.

Technical Advantages

Digitized Manufacture

The key processes including material cutting, rolling, drilling are made by advanced CNC machining process to reduce the assembly stress and extend boiler working lifetime.
The front and back smoke chamber plates are cut by CNC plasma cutting machine with tidy and beautiful look.

Easy Operation and Maintenance

Fully intelligent operation, with automatic adjustment and protection of burning, water level, temperature and steam pressure. The smoke box door uses the hinge structure for easy inspection, inventory and cleaning.

Long Service Life

The way to weld Smoke tube and tube sheet is to first expand to eliminate the gap between them, then adopt automatic argon arc welding to relief the stress and expand boiler service life.
Longitudinal and girth joint adopt advanced automatic submerged-arc welding for good welding quality. All longitudinal and girth joint are test by radiographic inspection.
Fin tube uses ND steel or stainless-steel material to avoid corrosion in the low temperature.
Inspection stops are set up to guarantee the sequence of expanding and welding to avoid cracking of the tube sheet holes.

Less Fuel Consumption

High quality aluminum silicate fiber is used with fire clay insulation, to control the boiler body temperature below 45℃ and reduce heat lost.
Sufficient steam storage room and heating area to generate high quality steam and high thermal power.
Condenser is added to recycle the waste heat of the exhausted smoke to increase feeding water’s temperature and reduce flue gas emission temperature and increase the thermal efficiency over 98% and save operating cost.

Boiler-Feed Pumps | Armstrong Internation

2019-10-28 · 4300 Series Stainless Steel Boiler Feed Pumps. 4300 Series Boiler Feed Pumps set new standards of performance. Reliable and efficient, each unit features heavy gauge, 3/16" stainless steel receivers for long operating life. In addition, 3450 RPM motors assure maximum efficiency while maintaining minimum motor horsepower.

Boiler Feed Water Pumps & Condensate Pumps

Large industrial condensate pumps may also serve as the feedwater pump. In either case, to force the water into the boiler, the pump must generate sufficient pressure to overcome the steam pressure developed by the boiler. This is usually accomplished through the use of a centrifugal pump.

Boiler Feed Pumps - Pumps by King Pumps: Wate

Pedrollo Close Coupled Peripheral Turbine Boiler Feed Pumps. The Pedrollo peripheral turbine pumps are recommended for pumping clean water without abrasives and liquids that are chemically compatible with the materials of construction.

Modern seal system for boiler feedwater pum

Modern seal system for boiler feedwater pumps Too much venting will draw hot process water past the throat bushing and into the Plan 23 loop, causing an increase of temperature of the water at the seal and o-rings. The ball float vent valve prevents this. Environment:

BOILER FEED & PUMP SIZING - cleaverbrooks.c

2018-8-5 · • Methods and importance of capturing condensate for boiler feed • Typical pumps used for boiler feed water discharge • Typical piping methods used • Pump sizing criteria • Criteria for calculating the base flow for the pump • Understanding TDH and NPSH • Sizing a pump for a

Boiler Feed Pumps | Insider Perspectives | Lubricolo

2019-10-19 · So, when a recent analysis by Trico of 12 months of oil sampling data from the bearings on boiler feed pumps at three power generation plants showed 95% had threateningly high levels of water and particulate contamination, we decided to do something about it. Why the Boiler Feed Pump Problem Is

China Hot Water High Pressure Boiler Feed Wate

Brief introduction Hot Water High Pressure Boiler Feed Water Pump is an efficient and energy-saving product designed for the new series of industrial steam boiler pumps. This series of pump mainly used for conveying water free of solid particles with the temperature is less than 160°C or physical and chemical properties similar to liquid water.

Hot water boilers | Grundf

2019-10-25 · Grundfos single-stage and multistage pumps for hot water boilers are available for temperatures up to 140°C. All pumps can be supplied with motors with a wall-mounted or integrated frequency converter (up to 22 kW), ensuring that the pressure and

Boiler Feed Water Pump manufacturers - Made-i

2019-10-24 · China Boiler Feed Water Pump manufacturers - Select 2019 high quality Boiler Feed Water Pump products in best price from certified Chinese Pump manufacturers, Water Pump suppliers, wholesalers and factory on Made-in-China.com

Boiler Feed Water System Diagram and Explanation

In case the hot well overflows, the water goes to the feed water tank, which supplies feed water to the system whenever there is a dearth. A de-aerated type heater is used in the feed water line in order to remove any dissolved oxygen from the water. This is basically done to prevent corrosion of the boiler.

Boiler feedwater pump - Wikiped

2019-10-15 · A boiler feedwater pump is a specific type of pump used to pump feedwater into a steam boiler.The water may be freshly supplied or returning condensate produced as a result of the condensation of the steam produced by the boiler. These pumps are normally high pressure units that take suction from a condensate return system and can be of the centrifugal pump type or positive